Detail 01
60W power rating
Double the headroom of many vintage-style 10s, so it stays clean under a mid-power amp instead of breaking up early.
Product detailSKU #1273887991513
CelestionG10 Vintage 60W, 10" Guitar Speaker 16 Ohm
Independent shopping perspective
The Korena take
A 10-inch guitar speaker rated at 60W, aimed at players building or reconing 1x10 and 4x10 cabinets who want a brighter, tighter voice.
Strong match
Who this is for
- Small combos and 4x10 cabs needing more power handling
- Players who want faster, tighter response than a 12
- Lightweight builds where a 5.3lb driver matters
Consider the trade-offs
When to look elsewhere
- Anyone chasing deep low end — it starts rolling off near 100Hz
- Bass guitar or full-range PA duty
- Cabinets cut for 12-inch drivers
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
100Hz-5500Hz range
Less low end and more top than a 12-inch speaker. Notes read tighter and cut better in a band.
Detail 03
97dB sensitivity
Moderate output per watt. In a 4x10 the combined array makes up the difference.
Detail 04
10-inch cone
Smaller cone moves faster, so attack is snappier and the low end firms up rather than blooms.
Detail 05
5.3lb unit weight
Four of these weigh less than two typical 12s, which keeps a 4x10 cabinet carryable.
Detail 06
4.1-inch overall depth
Shallow enough for thin combo cabinets where a deeper 12-inch driver would hit the back panel.
Final check
Know before you order
- 01Confirm the impedance you need — wiring several speakers changes the total load
- 02Bare driver. No gasket, screws, wire or terminals included
- 03Cabinet needs a 9.0-inch cutout and a 9.6-inch bolt circle
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01Can I mix these with 12-inch speakers?
Physically yes if the cabinet allows, but the 10s are brighter with less low end, so the two will not blend evenly.
02Is 60W enough for gigging?
For one speaker, it suits amps up to around 60W. In a 4x10 the cabinet handles considerably more since the load is shared.
03How does it compare to a 12 for tone?
Tighter and brighter. Response starts at 100Hz instead of the 75Hz a bigger driver reaches, and extends further up top.
04What size hole does it need?
A 9.0-inch cutout with a 9.6-inch bolt circle across four mounting slots, plus 4.1 inches of depth.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
3 detailsSound
- Frequency Range
- 100-5500Hz
- Sensitivity
- 97dB
- Resonance Frequency Fs
- 115Hz
1 detailsBody & build
- Voice Coil Material
- Round copper
1 detailsConnections & power
- Power Rating
- 60W
10 detailsSize & weight
- Nominal Diameter
- 10 inch, 254mm
- Voice Coil Diameter
- 1.75 inch, 44.5mm
- Weight
- 31
- Overall Depth
- 4.1 inch, 104mm
- Magnet Structure Diameter
- 5.3 inch, 134mm
- Diameter
- 10.1 inch, 256mm
- Magnet Weight
- 31 oz., 0.88kg
- Cut Out Diameter
- 9.0 inch, 229mm
- Mounting Slot Dimensions
- 0.2 x 0.3 inch, 6 x 8mm
- Unit Weight
- 5.3 lbs., 2.4kg
5 detailsOther
- Chassis Type
- Pressed steel
- Number of Mounting Slots
- 4
- Magnet Type
- Ceramic
- Mounting Slot Pcd
- 9.6 inch, 245mm
- DC Resistance Re
- 7.47 ohms
