Detail 01
60W handling with a ceramic magnet
Ceramic stays firm under power instead of sagging. Combined with 60 watts, it holds a clean note where an alnico would compress.
Product detailSKU #1273887991490
CelestionG10 Vintage 60W, 10" Guitar Speaker 8 Ohm
Independent shopping perspective
The Korena take
A 10-inch, 60-watt ceramic guitar speaker at 8 ohms. The high-headroom, lower-cost option for 1x10 through 4x10 guitar cabs.
Strong match
Who this is for
- Combos and cabs where the speaker should stay clean at volume
- 4x10 builds needing 240 watts of total handling
- Replacing a blown 10 without paying for alnico
Consider the trade-offs
When to look elsewhere
- Players chasing early speaker breakup and compression
- Anyone needing deep low end — response starts at 100Hz
- 12-inch baffles, without a new cutout
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
97dB sensitivity
Loud for the watts fed to it. Swapping in a lower-sensitivity speaker would drop volume noticeably at the same amp setting.
Detail 03
100–5500Hz frequency range
Rolls off below low E's fundamental and above the presence region — the usual guitar-speaker window, not full-range.
Detail 04
9.0 inch cutout, 9.6 inch bolt circle, 4 slots
These are the numbers that decide whether it bolts into your baffle. Measure them, not the 10.1-inch outer frame.
Detail 05
4.1 inch overall depth
Shallow enough for most combos, but check clearance behind the baffle if the cab is tight or has a rear brace.
Detail 06
1.75 inch copper voice coil, pressed steel chassis
A larger coil spreads heat over more area, which is part of how it reaches 60 watts. Pressed steel keeps weight at 5.3 lbs.
Final check
Know before you order
- 01Cutout is 9.0 inches with a 9.6-inch bolt circle — measure your baffle first
- 02DC resistance is 7.47 ohms; that is normal for an 8-ohm speaker, not a fault
- 03No mounting bolts, gasket or wiring — reuse the cab's existing hardware
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01Will four of these handle my 100-watt head?
Yes. Four at 60 watts each is 240 watts total, well above a 100-watt head. Wire them so the final load matches your amp's tap.
02Why does my meter read 7.47 ohms instead of 8?
That is the DC resistance, and 7.47 ohms is the published figure. Nominal impedance of 8 ohms is an AC rating and always reads higher than DC.
03Is it loud enough for a band?
97dB sensitivity is on the loud side for a 10, and it takes 60 watts. One handles small rooms; multiple speakers add level in a full band.
04How much does it weigh?
5.3 lbs, or 2.4kg, per speaker. The pressed steel chassis and ceramic magnet keep it light enough for a four-speaker cab.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
3 detailsSound
- Frequency Range
- 100-5500Hz
- Sensitivity
- 97dB
- Resonance Frequency Fs
- 115Hz
1 detailsBody & build
- Voice Coil Material
- Round copper
1 detailsConnections & power
- Power Rating
- 60W
10 detailsSize & weight
- Nominal Diameter
- 10 inch, 254mm
- Voice Coil Diameter
- 1.75 inch, 44.5mm
- Weight
- 31
- Overall Depth
- 4.1 inch, 104mm
- Magnet Structure Diameter
- 5.3 inch, 134mm
- Diameter
- 10.1 inch, 256mm
- Magnet Weight
- 31 oz., 0.88kg
- Cut Out Diameter
- 9.0 inch, 229mm
- Mounting Slot Dimensions
- 0.2 x 0.3 inch, 6 x 8mm
- Unit Weight
- 5.3 lbs., 2.4kg
5 detailsOther
- Chassis Type
- Pressed steel
- Number of Mounting Slots
- 4
- Magnet Type
- Ceramic
- Mounting Slot Pcd
- 9.6 inch, 245mm
- DC Resistance Re
- 7.47 ohms
