Detail 01
60W power rating
Handles a loud head on its own. Four in a cab give 240W total, which covers most guitar amps.
Product detailSKU #1273887991537
CelestionVintage 30 60W, 12" Guitar Speaker 16 Ohm
Sale
Independent shopping perspective
The Korena take
The 60W 12-inch Vintage 30 in 16 ohm. High output and high power handling for cabs that need to stay clean and loud.
Strong match
Who this is for
- High-wattage heads and 4x12 cabs
- Loud stages needing volume without speaker distress
- Replacing worn drivers in a gigging cabinet
Consider the trade-offs
When to look elsewhere
- Players chasing early speaker breakup at low volume
- Amps needing an 8 ohm load, unless wiring multiples
- Small combos where 10.4 lbs adds real weight
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
100dB sensitivity
Loud for the watts. Swapping this into a cab with a less sensitive speaker makes the rig noticeably louder at the same setting.
Detail 03
16 ohm nominal impedance
Matches a 16 ohm tap alone. Four in series/parallel land back at 16 ohm — the standard 4x12 wiring.
Detail 04
50oz ceramic magnet
The heavier magnet is where the extra output and tighter low-end control come from. It also adds cabinet weight.
Detail 05
75–5000Hz frequency range
Sharp rolloff above 5kHz keeps distorted tone from turning brittle. Not a full-range speaker.
Detail 06
5.3 inch depth, 11.1 inch cutout
Deeper than some 12s. Check rear clearance in shallow or closed-back cabs before buying.
Final check
Know before you order
- 01Speaker only — no wire, screws, gasket or terminals included
- 02Verify 16 ohm suits your amp, or plan multi-speaker wiring
- 0310.4 lbs each; four of them add over 40 lbs to a cab
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01Is this 8 or 16 ohm?
This listing is 16 ohm. The model is also made in 8 ohm, so check the amp tap you need before ordering.
02How do I wire four in a 4x12?
Series/parallel: two pairs in series, the pairs in parallel. Four 16 ohm speakers end at 16 ohm total, handling 240W.
03Can I use one with a 100W head?
A single 60W speaker is under-rated for a 100W head at full output. Use two or four, or keep the amp below full.
04Will this fit a standard 12 inch baffle?
It needs an 11.1 inch cutout, 11.7 inch mounting pattern and 5.3 inches of depth. Measure depth especially, as it is on the deeper side.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
4 detailsSound
- Frequency Range
- 75-5000Hz
- Nominal Impedance
- 8 ohms and 16 ohms
- Sensitivity
- 100dB
- Resonance Frequency Fs
- 75Hz
1 detailsBody & build
- Voice Coil Material
- Rounded copper
1 detailsConnections & power
- Power Rating
- 60W
10 detailsSize & weight
- Nominal Diameter
- 12 inch, 305mm
- Voice Coil Diameter
- 1.75 inch, 44.5mm
- Weight
- 50
- Overall Depth
- 5.3 inch, 135mm
- Magnet Structure Diameter
- 6.1 inch, 156mm
- Diameter
- 12.2 inch, 309mm
- Magnet Weight
- 50oz, 1.42kg
- Cut Out Diameter
- 11.1 inch, 283mm
- Mounting Slot Dimensions
- 0.31 inch, 7.9mm ¸
- Unit Weight
- 10.4lb, 4.7kg
5 detailsOther
- Chassis Type
- Pressed steel
- Number of Mounting Slots
- 4
- Magnet Type
- Ceramic
- Mounting Slot Pcd
- 11.7 inch, 297mm
- DC Resistance Re
- 7.3 ohms & 12.9 ohms
