Detail 01
2100W per channel at 4 ohms
Roughly 75 percent more per side than the 4002, and 1200W each into 8-ohm cabs. Real headroom for subs.
Product detailSKU #1296839766657
CrownXTi 6002 Power Amplifier
1/8
Independent shopping perspective
The Korena take
Two-channel amp with the same DSP as the 4002 and 2100W per channel at 4 ohms. For subwoofers and larger PA rigs that outgrew a smaller amp.
Strong match
Who this is for
- Driving double-18 or paired subs off one rack space
- Regional bands and production companies covering bigger rooms
- Installs where headroom matters more than power draw
Consider the trade-offs
When to look elsewhere
- Small rooms where the 4002 already has headroom to spare
- Venues with tight circuits — it wants its own breaker
- Quiet spaces; the fan scales up under load
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
6000W bridged at 4 ohms
Both channels drive one load. Enough for a large sub, but you give up the second output for mains.
Detail 03
15.3A under program, 180W idle
This wants a dedicated 20A circuit. Idle draw alone is nearly five times the 4002's, so it stays warm doing nothing.
Detail 04
Front-panel LCD
Shows the active preset and processing status, so you can confirm the right setup is loaded without hooking up a laptop.
Detail 05
16.2 inches deep, 24 lb
Four inches deeper and 5.5 lb heavier than the 4002. Measure shallow racks and leave room for cables behind it.
Detail 06
103 dB signal-to-noise
Residual hiss stays under the room, so an idle system between songs does not announce itself through the mains.
Final check
Know before you order
- 01Give it a 20A circuit; do not share with lighting
- 02Bridged operation is rated to 4 ohms — no lower
- 03Speakon and XLR cables are not included
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01Is it worth the jump from the 4002?
Only if you need the power. The DSP, connections and rack size match; you are paying for 2100W a side instead of 1200W, and heavier subs.
02Will it drive 2-ohm loads?
Yes — 3000W per channel at 2 ohms, so two 4-ohm cabs in parallel per side works. Watch the current draw at that load.
03Can it run without a computer?
Yes. The LCD and the sel/prev/next buttons cover preset changes and front-panel lockout. The USB connection is for deeper editing.
04What inputs does it take?
One XLR per channel, plus a link-out that loops the signal to another amp. RCA or unbalanced sources need an adapter or DI first.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
1 detailsSound
- Frequency Response (at 1 watt, 20 Hz - 20 kHz)
- +0 dB, -1 dB
4 detailsConnections & power
- Crosstalk (below rated power)
- 20 kHz - 1 kHz: > 70 db
- Sensitivity (for full rated power at 4 ohms)
- 1.4 Vrms
- Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms)
- 103 dB (A weighted)
- AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per channel)
- 15.3A; no more than 180W at idle
43 detailsOther
- Chassis
- Steel
- Stereo, 2 ohms (per ch.)
- 3000W
- -10 Indicator
- Green LED flashes when output signal exceeds -10 dB below clip.
- LCD Screen
- backlit liquid crystal display that shows preset and processing status
- Ready Indicator
- Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
- Input EQ
- 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
- Total Harmonic Distortion (THD)
- <0.5%
- Stereo, 8 ohms (per ch.)
- 1200W
- Delay
- for signal alignment of driver; 50 mS of total delay.
- Power Switch
- On/Off switch applies AC power to the amplifier
- Clip Indicator
- Red LED, one per channel, turns on at the threshold of audible distortion
- Output Connectors
- Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
- Output EQ
- 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
- Presets
- 30 total presets, 29 of which are user-definable.
- Tier
- new
- Bridge-Mono, 4 ohms
- 6000W
- Peak x Plus Limiter
- user defeatable limiter that allows users to control Threshold, Attack, and Release times.
- Signal Indicator
- Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
- Temp Indicator
- Red LED, one per channel, illuminates under excessive temperature conditions
- Front Panel
- Cast-aluminum
- Category Source
- detail
- Damping Factor 20 Hz to 1 kHz
- >500
- Operating Temperature
- 0C to 40C at 95% relative humidity (non-condensing)
- Maximum Input Signal
- +22 dBu typical
- Cooling
- Proportional speed fan with front-to-rear airflow.
- AC Line Voltage and Frequency Configurations
- 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
- Input Connectors
- XLR, one per channel
- Dimensions
- 19" (W) x 3.5" (H) x 16.2" (D)
- Stereo, 4 ohms (per ch.)
- 2100W
- Korena Special
- false
- Bridge-Mono, 8 ohms
- 4200W
- SubHarmonic Synth
- takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
- Sel/Prev/Next Buttons
- three buttons near the LCD screen that are used to access menu items and front panel lockout
- -20 Indicator
- Green LED flashes when output signal level exceeds -20 dB below clip.
- Crossover Filters
- Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ±15 dB bandpass gain and polarity control.
- Power Indicator
- Blue LED illuminates when the amplifier has been turned on and has power
- Link/Out Connector
- Loop-thru signal from input connector for linking another amplifier, one per channel.
- HiQnet USB Connector
- Type B, connects to HiQnet network.
- Level
- two front-panel rotary level controls, one for each channel
- Source Id
- site51296839766657
- Prop65
- WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov.
- Net Weight
- 24.0 lb. (10.9kg)
- Input Impedance (nominal)
- 20k ohms balanced, 10k ohms unbalanced
Worth comparing
1 of 12
More from Crown
1 of 7
