Detail 01
2 x 1,800 W into 4 ohms
Provides the stated 3,600 W total output across two channels at 4 ohms.
Product detailSKU #1500000213066
DYNACORDL3600FD DSP Power Amplifier
1/5
Independent shopping perspective
The Korena take
DYNACORD’s L3600FD is a two-channel DSP power amplifier rated at 3,600 watts total, or 1,800 watts per channel into 4 ohms. It is built around live-sound system control: each channel has 10-band parametric EQ, and Ethernet access opens its DSP feature set and factory-optimized FIR Drive settings. Locking power and Ethernet connections, speakON outputs, front-panel controls, and an infrared remote support day-to-day PA operation.
Strong match
Who this is for
- Live PA systems needing two 1,800 W channels into 4-ohm loudspeaker loads.
- Sound engineers shaping each amplifier channel with onboard parametric EQ and Ethernet-accessed DSP.
- Multi-amplifier systems that use the unit’s linkable design for expanded power and processing.
Consider the trade-offs
When to look elsewhere
- Mains environments that do not match the amplifier’s factory-configured 100 V, 120 V, 230 V, or 240 V requirement.
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
10-band parametric EQ per channel
Lets each channel be adjusted independently from the amplifier’s DSP.
Detail 03
speakON outputs
Uses speakON speaker-output connections.
Detail 04
Front-to-rear, three-stage fans
Cooling airflow is specified to run from the front to the rear.
Final check
Know before you order
- 01Confirm the factory-configured mains voltage: 100 V, 120 V, 230 V, or 240 V at 50–60 Hz.
- 02Use Ethernet to access the amplifier’s full DSP feature set.
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01How much power does the L3600FD deliver into 4 ohms?
It is rated at 2 x 1,800 W into 4 ohms, for 3,600 W total.
02Can I control DSP settings over a network?
Yes. Ethernet provides access to the full range of DSP features.
03What speaker outputs does it use?
It has speakON outputs.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
1 detailsSound
- Frequency Response Ref 1 KHZ
- 10 Hz to 21 kHz (±1 dB)
6 detailsConnections & power
- Power Requirements
- 240 V, 230 V, 120 V or 100 V; 50 Hz to 60 Hz (factory configured)
- Maximum RMS Voltage Swing Thd 1 1 KHZ
- 90.6 V
- Voltage Gain Ref 1 KHZ
- 32.0 dB
- Power Consumption 1 8 Maximum Output Power 4
- 850 W
- Output Stage Topology
- Class H
- Maximum Input Level
- +21 dBu
2 detailsSize & weight
- Signal to Noise Ratio Amplifier A Weighted Ref to Max Output Power 8
- > 109 dB
- Output Noise A Weighted
- < -68 dBu
8 detailsOther
- Mains Fuse
- 240 V/230 V: T15AH; 120 V/100 V: T30AH
- Protection
- Audio limiters, high temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters, Turn on delay
- Crosstalk Ref 1 KHZ At 100w 4
- < -80 dB
- Thd At 1200 W 4 Mbw 80 KHZ 1khz
- < 0.05%
- Dim30 3 15 KHZ 15 KHZ
- < 0.05%
- Imd Smpte 60 HZ 7 KHZ
- < 0.1%
- Ambient Temperature Limits
- +5°C to +40°C (40°F to +105°F)
- Cooling
- Front-to-rear, 3-stage-fans
