Detail 01
Rated to 16,000+ flex cycles
Survives repeated coiling and chair-rolling without the conductor fatiguing at the strain point.
Product detailSKU #1275776902291
MogamiGold Headphone Extension Cable 10 ft.
Independent shopping perspective
The Korena take
A 10 ft headphone extension cable from Mogami. For studio or desk setups where the headphone jack sits farther away than the stock cord reaches.
Strong match
Who this is for
- Tracking rooms where the headphone amp is across the space
- Desk setups with the interface rack-mounted or behind the monitor
- Long-session use where cable handling and flex matter
Consider the trade-offs
When to look elsewhere
- Anyone needing a replacement cable rather than an extension
- Budget headphone setups where the cable outcosts the headphones
- Players wanting a coiled or retractable cord
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
Microphonics held to 30-40 mV max
Cable rubbing against a chair or shirt transmits far less handling rumble into the ears.
Detail 03
57 pF/m capacitance
Low enough that a 10 ft run doesn't audibly roll off the top end on high-impedance headphones.
Detail 04
-4 F to 158 F operating range
Handles a hot rack, a cold garage, or an outdoor stage without the jacket stiffening or softening.
Detail 05
Inner conductor DC resistance 0.083 ohm/m
Series resistance stays tiny, so headphone damping and volume aren't affected across the added length.
Detail 06
Non-emigrant to ABS resin
The jacket won't leach plasticizer into plastic gear it rests against and leave sticky marks.
Final check
Know before you order
- 01This extends an existing cable — it does not replace your headphone cord
- 02Check whether your headphones use 1/4 in or 1/8 in before ordering
- 03No adapter is included; add one if your jack sizes differ
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01Will this work with any headphones?
It works with headphones that use a standard removable or plug-terminated cord. Check that your headphone plug and your amp jack both match the cable's connector size before ordering.
02Does 10 feet of extra cable hurt the sound?
No. Capacitance and conductor resistance are low enough over this length that there's no audible change in level or high-frequency response.
03Is it worth this much for an extension cable?
The cost is in the construction — high flex life, low microphonics, and a durable jacket. If you coil and uncoil it daily, that matters. For a cable that sits still, less so.
04Can I use it for anything other than headphones?
It's built and terminated as a headphone extension. Use an instrument or patch cable for signal runs between gear.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
1 detailsSound
- Characteristic Impedance 10mhz
- 75W
1 detailsBody & build
- Color
- Black
1 detailsConnections & power
- Voltage Breakdown
- Must withstand at DC 500V/15sec.
1 detailsIn the box
- Standard
- UL2552 AWM 30V 60 deg C VW-1
13 detailsOther
- Phase Constant 10mhz
- 0.3 rad/m
- Shield
- 0.025W/m(0.0076W/Ft): 0.025W/m(0.0076W/Ft)
- Insulation Resistance
- 100000 M W … m Min. at DC 125V, 20 deg C
- Emigration
- non-emigrant to ABS resin
- Capacitance At 1khz 20 Deg C
- 57pF/m(17.4pF/Ft): Ref. Quad Mic. Cables
- Flex Life
- 16,000 cycles: 16,500 cycles: 26,000 cycles
- Electrostatic Noise
- 50m V Max.: 50m V Max.
- Microphonics At 50kw Load
- 40m V Max.: 30m V Max.
- Inductance Between Conductors At 1khz 20 Deg C
- 0.4H/m(0.12H/Ft): 0.5H/m(0.15H/Ft)
- Applicable Temperature
- -20 deg C +70 deg C(-4 deg F +158 deg F)
- Tensile Strength
- 274N: 539N: 500N
- DC Resistance At 20 Deg C
- Inner Cond.: 0.083W/m(0.025W/Ft); 0.13W/m(0.040W/Ft)
- Attenuation 10mhz
- 0.0608 dB/m
