Detail 01
6HP (30 mm) width; 33 mm depth including power connector
Use these dimensions when planning available Eurorack case space.
Product detailSKU #1500000468066
UDO AudioRBN-1-C Performance Ribbon Eurorack Receiver
1/3
Independent shopping perspective
The Korena take
The RBN-1-C brings UDO’s RBN-1 Ribbon Controller into a Eurorack system through a compact 6HP receiver. Its 3.5 mm TRS ribbon connection feeds two CV and gate output paths with 1V/octave scaling, so each hand can be routed separately within a patch. An externally triggered live looper records and plays back ribbon gestures, while adjustable ribbon behavior, gate LEDs, and output protection keep its operation visible and configurable. At 33 mm deep including its power connector, it is sized for shallow-case planning.
Strong match
Who this is for
- Adding separate hand-controlled CV and gate gestures to an Eurorack performance patch.
- Recording ribbon gestures into the onboard looper for externally triggered playback.
- Fitting UDO RBN-1 ribbon control into a compact Eurorack case.
Consider the trade-offs
When to look elsewhere
- Use with ribbon controllers other than the UDO RBN-1 Ribbon Controller is not supported by the listed compatibility.
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
Dual CV and gate outputs
The module provides two separate CV/gate output paths.
Detail 03
1V/octave scaling
Its listed output scaling is 1V per octave.
Detail 04
Live looper with trigger input
Ribbon gestures can be recorded and replayed when triggered from an external source.
Detail 05
Per-channel gate LEDs
Each channel lights red when its gate output is high.
Final check
Know before you order
- 01It is compatible with the UDO RBN-1 Ribbon Controller.
- 02It requires a 2x5 0.1-inch keyed Eurorack power connection using 0V, +12V, and -12V.
- 03Allow 33 mm of case depth when the power connector is included.
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01Which ribbon controller works with the RBN-1-C?
It is listed as compatible with the UDO RBN-1 Ribbon Controller.
02Can it record ribbon movement?
Yes. Its live looper records and replays gestures, with an external trigger input for the looper.
03How much rack space does it need?
The module is 6HP wide, or 30 mm, and is 33 mm deep including its power connector.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
1 detailsPickups & controls
- Short Circuit Protection
- Yes (1k 250mW series resistors)
1 detailsPlayability
- Full Scale Error
- Maximum +/-8mV
1 detailsBody & build
- Panel Material
- Aluminum
9 detailsConnections & power
- Dual Cv Gate Outputs
- Yes
- Power Supply Connector
- 2x5 0.1 inch keyed, Eurorack compatible
- Supply Voltage Tolerance
- +/-12V +/-10%
- Input Resistance Range
- 5k–25k
- Input Impedance
- >10k
- Output Type
- 3.5 mm TS jack sockets
- Input Type
- 3.5 mm TS jack socket
- Trig Input For Looper
- Yes
- Power Supply Input
- 0V, +12V, -12V
3 detailsSize & weight
- Max Height
- 16 mm
- Width
- 6HP (30 mm)
- Depth Including Power Connector
- 33 mm
13 detailsOther
- Zero Point Error
- Maximum +/-8mV
- Ribbon Behavior Settings
- Adjustable
- Looper Functionality
- Yes
- Logic Level
- 0/5V, active high
- Tip Function
- Wiper input
- Panel Thickness
- 2 mm
- Scaling
- 1V/octave
- Format
- Eurorack
- Shield Function
- Ground
- Supply Current
- +30mA / -15mA
- Gate Indicators
- LED per channel (illuminated red when gate output is high)
- Ring Function
- Ribbon supply voltage
- Compatibility
- UDO RBN-1 Ribbon Controller
