Detail 01
DDT circuitry
Distortion Detection Technique is stated to protect drivers and maintain sonic integrity during extreme overload conditions.
Product detailSKU #1378824449369
PeaveyIPR2 3000 Power Amp
aggressivehigh output
1/8
Independent shopping perspective
The Korena take
A lightweight, high-output two-channel power amplifier with Class D efficiency, switchable crossover functions, and protection circuitry for demanding loads and power conditions.
Strong match
Who this is for
- Users needing two-channel power down to 2-ohm loads
- Rigs that benefit from high output in a lightweight amplifier
- Setups needing onboard high-pass or low-pass crossover selection
Consider the trade-offs
When to look elsewhere
- Users needing an amplifier specified only for loads above 2 ohms
- Setups that do not need a two-channel power amplifier
- Users seeking specifications not stated for this model
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
2-ohm operation
The amplifier is specified to operate into loads as low as 2 ohms.
Detail 03
Class D with switch-mode power supply
The design is stated to reduce weight while increasing output power, reliability, and thermal efficiency.
Detail 04
Switchable crossover
Each channel has a 100Hz 2nd-order high-pass and 3rd-order low-pass option.
Final check
Know before you order
- 01Confirm your speakers and wiring support the intended load impedance; the minimum specified load is 2 ohms.
- 02Check the stated output figures at your intended impedance and distortion rating.
- 03Verify the listed combo/XLR inputs, XLR thru connections, and twist-lock outputs suit your system.
- 04Allow for fan cooling and confirm the 19-inch rack width and 10.5-inch behind-panel depth fit your installation.
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01What is the minimum supported load?
The stated minimum load impedance is 2 ohms.
02How much power does it provide at 4 ohms?
With both channels driven at 1kHz, it is rated at 900W per channel at 1% THD, 815W per channel at 0.2% THD, or 950W per channel in a 20ms repetitive burst.
03Does it include crossover controls?
Yes. It has a switchable 100Hz 2nd-order high-pass and 3rd-order low-pass crossover per channel.
04What connections are provided?
It has dual combination 1/4-inch/XLR inputs, dual male XLR input thru connections, and two twist-lock connectors.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
2 detailsConnections & power
- Current Draw @ 1/8 power in VA (watts)
- 960 (535) @ 2 ohms, 615 (315) @ 4 ohms, 400 (200) @ 8 ohms
- Current Draw @ 1/3 power in VA (watts)
- 2065 (1360) @ 2 ohms, 1215 (735) @ 4 ohms, 740 (420) @ 8 ohms
26 detailsOther
- Voltage Gain
- x 75 (+37dB)
- Crosstalk
- > -68 dB @ 1 kHz @ 400 watts @ 8 ohms Hum and Noise: > -101.5 dB, "A" weighted referenced to rated power @ 4 ohms Slew Rate: > 12V/μs Damping Factor (8 ohms): > 215:1 @ 20 Hz - 1 kHz @ 8 ohms
- Input CMRR
- > - 76dB @ 1kHz
- 20Hz - 20kHz 2ch x 4 ohms
- <0.15% @ 650 watts 20 Hz to 20 kHz, both ch. driven
- Input Sensitivity
- .775 volts +/- 3% for 1kHz 4 ohm rated power, .73 volts +/- 3% for 1kHz, 2 ohm rated power Input Impedance: 15kOhms, balanced and 7.5k ohms unbalanced
- Tier
- new
- Controls
- Two front panel attenuators, crossover select switch for HPF, Normal and LPF Indicator LEDs: Five LED indicators per channel: Active, Signal, DDT, Temperature and DC
- Frequency Response
- 20Hz - 22kHz; +/-.05dB @ 4 ohms
- Protection
- Thermal, DC, subsonic, incorrect loads, under and over voltage
- 20Hz - 20kHz 2ch x 2 ohms
- <0.15% @ 1,200 watts 20Hz to 3kHz, decreasing to 1,100 watts @ 20kHz, both ch. driven
- Category Source
- detail
- Construction
- 0.062" aluminum
- 20Hz - 20kHz 2ch x 8 ohms
- <0.15% @ 375 watts 20 Hz to 20 kHz, both ch. driven
- Cooling
- Temperature dependent variable speed 80mm DC fan
- Rated Watts 2ch x 4 ohms
- 950 watts 20ms repetitive burst / 900 watts 1% THD / 815 watts 0.2% THD, both ch. driven @ 1kHz
- Dimensions
- 3.5" x 19" x 10.5" behind front panel + 0.6" for handle
- Korena Special
- false
- Rated Watts 2ch x 2 ohms
- 1750 watts 20ms repetitive burst / 1450 watts 1% THD both ch. driven @ 1kHz
- Weight
- 5.62kg (12.4 lb.* )
- Idle Consumption
- 160VA, 75 watts
- Connectors
- Dual combination 1/4" & XLR, dual male XLR input thru, two twist lock connectors
- Rated Watts 2ch x 8 ohms
- 525 watts 20ms repetitive burst / 500 watts 1% THD / 430 watts 0.15% THD, both ch. driven @ 1kHz
- Minimum Load Impedance
- 2 ohms
- Source Id
- site51378824449369
- Crossover
- 100Hz switchable 2nd order high pass and 3rd low pass per channel
- Maximum RMS Voltage Swing
- 70V
Worth comparing
1 of 12
