Detail 01
Up to 12 monitor outputs
Supports custom speaker configurations with as many as 12 output channels.
Product detailSKU #1500000338172
FocusriteRedNet R1 Remote Controller for Red Interfaces With PoE
1/5
Independent shopping perspective
The Korena take
RedNet R1 is a hands-on monitor-control and routing remote for Focusrite Red interfaces. It can manage monitor layouts from mono to 7.1.4, including immersive workflows, or a custom configuration of up to 12 outputs. From the surface, you can handle level, cut, dim, mute, solo, A/B monitoring and fold-down checks, then route cue mixes and talkback where they are needed. RedNet Control2 handles configuration for both straightforward and more involved monitoring systems.
Strong match
Who this is for
- Studios moving between mono, surround, 7.1.4, or custom monitor configurations.
- Control rooms needing fast A/B, fold-down, cut, dim, mute, and solo monitoring checks.
- Sessions that need custom cue mixes and talkback routing from available input channels.
Consider the trade-offs
When to look elsewhere
- Monitoring systems requiring more than 12 monitor output channels.
- Workflows that need more than eight simultaneously selectable input sources.
- Non-Red Dante-device setups requiring more than one talkback destination group.
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
Eight sources from 32 available channels
Allows selection and routing of up to eight input sources across the available channels.
Detail 03
Up to four fold-down presets
Enables quick switching when checking downmixes.
Detail 04
PoE or supplied 12V DC power
Can be powered over Ethernet or from the supplied locking-barrel DC supply.
Detail 05
32–600 ohm headphone impedance
The headphone output is specified for headphones within that impedance range.
Final check
Know before you order
- 01Configure monitoring and routing through RedNet Control2.
- 02For up to four talkback destination groups, use RedNet R1 with a Red interface; other Dante devices support one group.
- 03Confirm your network power meets IEEE 802.3af PoE requirements if powering the unit over Ethernet.
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01How many monitor outputs can RedNet R1 control?
It can mix and route to up to 12 monitor output channels, including custom configurations of up to 12 outputs.
02Can it control immersive monitoring?
Yes. It supports monitor configurations through 7.1.4, including Dolby Atmos and other immersive workflows.
03How is RedNet R1 powered?
It can run from IEEE 802.3af Power over Ethernet or the supplied 12V DC power supply.
04Does it have talkback facilities?
Yes. It has Dante-enabled talkback, an internal microphone, an external XLR talkback input, and a footswitch jack for talkback management.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
2 detailsSound
- Headphone Impedance
- 32 Ohm -600 Ohm
- Frequency Response
- 20Hz to 20kHz ±0.5dB
4 detailsPickups & controls
- Control Functions
- 2 x Continuous Pot (Level & Dim)
- Power Switch
- 1 x Switch•Talkback Gain Pot: 1 x Pot
- Foot Switch
- 1 x 1/4 inch stereo jack
- Talkback Switch
- 1 x Tri-State Switch (External Talkback + 48V, External Talkback and Internal Talkback)
2 detailsBody & build
- Color
- Red
- Type
- Electronically Balanced, Zin = 3kΩ
10 detailsConnections & power
- Mic Input to Headphone Output
- < -122dB; 20Hz–20kHz (all other channels at 0dBFS)
- Power Over Ethernet Poe
- Complies with IEEE 802.3af class 0 Power-over-Ethernet standard (PoE A or PoE B compatible)
- Headphone Outputs
- 1 x 1/4 inch stereo jack
- External Talkback Mic Input
- 1 x XLR (F)
- Supported Sample Rates
- 44.1 / 48 / 88.2 / 96 kHz (-4% / -0.1% / +0.1% / +4.167%) at 24-bit
- DC Power Supply
- 1 x 12V 1.2A DC Power Supply
- Output Impedance
- 5 Ohm
- Power Consumption
- PoE: 10.3W -DC: 9W (When using supplied DC PSU)
- Max Input Level
- +10dBu ± 0.5dB
- Headphone Output to Mic Input
- < -84dB; 20Hz–20kHz (all other channels at 0dBFS)
14 detailsOther
- Signal to Noise Ratio
- -111dB 'A'-Weighted (typical), min gain
- Psu Poe and DC
- 1 x PoE Input and 1 x DC 12V Locking Barrel Input Connector
- Left to Right
- < -85dB; 20Hz–20kHz (all other channels at 0dBFS)
- Ein
- < -128dBu 'A'-Weighted (typical)
- Thd N
- -100dB (0.001%) @ -1dBFS, Rs = 150R
- Noise in Presence of Signal Nipos
- > -97 dBu 'A-Weighted'
- Clock Sources
- Internal or from Dante Network Master
- Operating Temperature
- Operates at up to an ambient temperature of 40-degrees Celsius
- 0 Dbfs Reference Levels
- +11dBm
- Common Mode Rejection Ratio
- 50/60Hz CMRR: <-77db
- Right to Left
- < -85dB; 20Hz–20kHz (all other channels at 0dBFS)
- Gain Range
- 0dB to 55dB
- LCD Screens
- 2 x Screens (Control, Status, Metering & Menus)
- Dynamic Range
- 108dB 'A'-weighted (typical), 20Hz -20kHz
