Korena
Product detailSKU #1500000483326

Warm AudioReamper Analog Routing Device With Instrument Preamp - Brown

Warm Audio
Warm Audio Reamper Analog Routing Device With Instrument Preamp - Brown
1/7

Independent shopping perspective

The Korena take

The WA-RA is an all-analog routing device for bringing instrument, line-level, pedal, rack, and amplifier paths together in a recording setup. Its independent preamp and re-amp sections allow a guitar to be tracked through an amplifier while a dry signal is retained for later processing. Variable impedance, selectable JFET input stages, transformers, phase inversion, ground lift, and continuously adjustable re-amp level give engineers control over how sources enter and leave the chain. Its integrated 50W/8-ohm power soak also supports speaker-free tube-amp recording within those limits.

Warm Audio Reamper Analog Routing Device With Instrument Preamp - Brown product detail
Product studyWarm Audio Reamper Analog Routing Device With Instrument Preamp - Brown
Warm Audio Reamper Analog Routing Device With Instrument Preamp - Brown alternate view
Alternate view

Strong match

Who this is for

  • Recording a guitar through an amplifier while retaining a dry track for later re-amping.
  • Inserting guitar pedals into balanced line-level paths for vocals, drums, or synthesizers.
  • Capturing a tube amplifier without a speaker cabinet in controlled or late-night recording sessions.

Consider the trade-offs

When to look elsewhere

  • Using the integrated speaker power soak with an amplifier above its 50W maximum rating.
  • Using the integrated speaker power soak with a speaker connection other than its specified 8-ohm load.

What matters in use

The specifications, translated

Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.

Warm Audio Reamper Analog Routing Device With Instrument Preamp - Brown construction detail

Detail 01

Independent preamp and re-amp paths

Supports separate tracking and re-amping workflows within the same device.

Detail 02

120 kOhm–1 MOhm variable impedance

Lets the input be adjusted for passive and active sources.

Detail 03

Switchable JFET discrete or JFET op-amp input stage

Provides a choice between the two input-stage options.

Detail 04

50W maximum, 8-ohm speaker power soak

Permits speaker-free tube-amp recording only within the stated power and impedance limits.

Detail 05

XLR and 1/4-inch line I/O

Connects to balanced studio line-level paths using either connection type.

Final check

Know before you order

  1. 01The speaker power soak is specified for 8 ohms and a maximum of 50W.
  2. 02The unit requires 90–240V AC, 50–60Hz power through its IEC input.
Warm Audio Reamper Analog Routing Device With Instrument Preamp - Brown close-up

Product questions

Before you decide

Straight answers to the questions shoppers most often ask about this product.

01Can I keep a dry guitar signal while tracking through an amp?

Yes. The independent paths support tracking through an amplifier while capturing a dry signal for later re-amping or processing.

02Can I record a tube amp without a speaker cabinet?

Yes, using the integrated 50W/8-ohm power soak with amplifiers up to 50W.

03Can it place pedals into studio line-level chains?

Yes. It supports inserting guitar pedals into balanced, line-level paths.

Reference

Full specifications

The complete catalog record, organized around the decisions musicians make when comparing gear.

1 detailsSound
Variable Impedance
120 kOhm to 1 MOhm
2 detailsPickups & controls
Controls
Input select, JFET/op-amp, variable impedance, preamp level, reamp level, phase invert, ground lift, power
Circuit Design
Fully active low-noise design
1 detailsBody & build
Color
Brown
13 detailsConnections & power
Reamp Output Level
Stepless attenuation to gain
Thru Outputs
Instrument thru, amp thru
Instrument Input
1 x 1/4 inch
Reamp Output
1 x 1/4 inch
Balanced Line Output
True line level
Maximum Instrument Input Level
+18 dBu
Input Stage
Switchable JFET discrete or JFET op-amp
Line Outputs
XLR, 1/4 inch
Line Inputs
XLR, 1/4 inch
Speaker Power Soak
8 ohm, 50W max
Power Requirement
90–240 V AC, 50–60Hz
Power Input
IEC
Speaker Input
1
4 detailsSize & weight
Height
4.20 inch
Weight
3.6
Depth
6.40 inch
Width
11.70 inch
7 detailsOther
Ground Lift
Per channel
Model
WA-RA
Processing Type
All-analog signal path
Transformers
CineMag USA input and output
Phase Invert
Per channel
Product Type
Reamp and instrument preamp
Channels
2