Detail 01
Four-channel receiver
One AD4QNP receives four channels.
Product detailSKU #1500000328592
ShureAxient Digital AD4QNP Four-Channel Receiver - (Receiver Only) Band A Band A
1/3
Independent shopping perspective
The Korena take
Shure’s Axient Digital AD4QNP is a four-channel receiver in the receiver-only Band A version. It works with all Axient Digital transmitters and brings wide tuning, low latency, High Density mode, and Quadversity to a networked wireless workflow. AES3, AES67, and Dante routing options provide several paths for managing its audio and signal routing. Network addressing can be set through DHCP or a manual IP address, making it suited to systems where receiver control and routing are planned as part of the wider setup.
Strong match
Who this is for
- Multi-channel Axient Digital wireless setups that need networked receiver control and flexible digital audio routing.
- Workflows using AES3, AES67, or Dante signal-routing options.
- Systems using Axient Digital transmitters with a receiver in the listed Band A range.
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
DHCP or manual IP addressing
The receiver can join a network through automatic addressing or a manually assigned IP address.
Detail 03
AES3, AES67, and Dante
These are the listed signal-routing options for integrating the receiver into its audio workflow.
Detail 04
44 mm x 483 mm x 333 mm
Use these dimensions when planning the receiver’s physical placement.
Final check
Know before you order
- 01Confirm that the receiver-only Band A version and its listed 470–636mHz RF carrier range suit the system plan.
- 02Plan for 100–240V AC, 50–60Hz power.
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01How many channels does the AD4QNP receive?
It is a four-channel receiver.
02Which transmitters work with it?
It is compatible with all Axient Digital transmitters.
03Does it support Dante?
Yes. Dante is listed alongside AES3 and AES67 signal-routing options.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
3 detailsSound
- Impedance
- 50 ohm
- Rf Carrier Frequency
- AD4Q=A: 470–636mHz, AD4Q=B: 606–810mHz, AD4Q=C: 750–960mHz
- Impedance Typical XLR Line Out
- 100ohm
1 detailsPickups & controls
- Mic Line Switch
- 30dB pad
1 detailsPlayability
- Full Scale Output
- 1/4 inch (6.35 mm): +8 dBVXLR
1 detailsBody & build
- Color
- (Receiver Only) Band A Band A
4 detailsConnections & power
- Connector Type
- BNC
- Phantom Power Protection
- Yes
- Power Requirements
- 100 to 240V AC, 50–60Hz; .68A max.
- Bias Voltage
- 12–13.5 V DC, 150 mA maximum, per antenna, switchable on/off
3 detailsSize & weight
- Dimensions Hxwxd
- 44 mm × 483 mm × 333 mm (1.7 inch x 19 inch x 13.1 inch)
- Weight
- 4.8
- Maximum Ethernet Cable Length
- 100 m (328')
12 detailsOther
- Note
- For connection of one additional receiver in the same band
- Housing
- Steel; Extruded aluminum
- Configuration
- Unbalanced, passive
- Network Addressing Capability
- DHCP or Manual IP address
- Thermal Dissipation
- Maximum: 31W (106 BTU/hr.)
- 200 Kohm Load
- XLR: LINE setting= +18 dBV, MIC setting= –12 dBV
- Spurious Rejection
- >80dB, typical
- Idle
- 21W (72 BTU/hr.)
- Insertion Loss
- 0dB, typical
- Gain Adjustment Range
- –18 to +42dB in 1dB steps (plus Mute setting)
- Network Interface
- 10/100 Mbps, 1 Gbps, Dante Digital Audio
- XLR
- Transformer-coupled Balanced (1=ground, 2=audio +, 3=audio -)
