Detail 01
400W per channel at 8 ohms, 800W at 4 ohms
Power doubles when you run two cabinets per side. One 8-ohm top per side gets 400W, not 800W.
Product detailSKU #1275776902435
BehringerEUROPOWER PMP6000 20-Channel 1,600W Powered Mixer
1/4
Independent shopping perspective
The Korena take
Powered 20-channel mixer with 1,600W of onboard amplification and effects. For bands and small venues that want one box instead of a mixer plus amp rack.
Strong match
Who this is for
- Bar and club gigs running passive mains and monitors
- Houses of worship needing one operator and one box
- Portable PA where truck space and setup time matter
Consider the trade-offs
When to look elsewhere
- Studios — this is a live console with no multitrack output
- Rigs already using powered speakers, which duplicates the amps
- Anyone needing digital recall, scenes, or motorized faders
What matters in use
The specifications, translated
Catalog numbers tell only part of the story. These are the details most likely to change how this product feels, sounds, or fits into a setup.
Detail 02
Bridged mode, 1,200W RMS at 8 ohms
Combines both amps into one channel for a single big system. You lose separate monitor amplification doing it.
Detail 03
Three-band EQ: 80Hz low, sweepable 100Hz-8kHz mid, 12kHz high
The sweepable mid is the useful one — it lets you hunt and cut feedback frequencies instead of guessing.
Detail 04
4-8 ohm main and monitor outputs
Do not go below 4 ohms per side. Three 8-ohm cabinets on one output drops to 2.7 ohms and risks shutdown.
Detail 05
Mic EIN -134dB
Preamp noise floor is low enough that quiet dynamic mics with lots of gain stay usable.
Detail 06
1,050W power consumption
Draws real current at full tilt. On a shared 15A circuit with lights, expect breaker trouble.
Detail 07
23-1/2 x 4-7/8 x 19-1/2 inches
Rack-width but deep. Measure your case — the depth is what usually doesn't fit.
Final check
Know before you order
- 01Speakers, speaker cable, mics and stands are all separate purchases
- 02Needs unpowered passive speakers — powered cabinets make the built-in amps dead weight
- 03Give it air on both sides; blocked fan intakes cause thermal shutdown mid-set
Product questions
Before you decide
Straight answers to the questions shoppers most often ask about this product.
01How many speakers can I connect?
Two 8-ohm cabinets per output side gets you to a 4-ohm load, the minimum. Going lower risks protection cutting out.
02Can I use this with powered speakers?
Yes, via the line outputs, but you'd be paying for 1,600W of amplification you never use. An unpowered mixer makes more sense.
03Is 1,600W enough for a 200-person room?
For a full band in a bar-sized room, yes, with efficient cabinets. Outdoors or with heavy low end, you'll want more.
04Does it record to a computer?
There's no multitrack USB interface here. It's built to mix and amplify a live show, not capture separate channels.
Reference
Full specifications
The complete catalog record, organized around the decisions musicians make when comparing gear.
3 detailsSound
- Impedance Approx
- 3.6 kohm
- Impedance
- approx. 1 kohm
- Frequency Response
- < 10Hz-200kHz (-1dB), < 10Hz - > 200kHz (-3dB)
1 detailsPickups & controls
- Bridge
- 8–16 ohm
3 detailsBody & build
- Color
- Red
- Type
- 2 x 2-digit, 7-segment LED
- RMS 1 Thd Bridged Mode
- 8 ohm 1200W
5 detailsConnections & power
- Max Output Level
- +21dBu
- Mains Connector
- IEC standard receptacle
- Power Consumption
- 1050W
- Max Input Level
- +21dBu
- Peak Power Bridged Mode
- 8 ohm 1600W
2 detailsSize & weight
- Dimensions Wxhxd
- 23-1/2 inch x 4-7/8 inch x 19-1/2 inch, 596 mm x 122 mm x 496 mm
- Weight
- 10.4
20 detailsOther
- Usa Canada
- 120V, 60Hz
- Converter
- 24-bit Delta-Sigma, 64/128-times oversampling
- Signal to Noise Ratio
- 109dB/112dB A-weighted (0dBu In @ +10dB gain)
- Mid
- 100Hz-8kHz/±15dB
- Main Mono Main Mono
- 4–8 ohm
- Gain
- +10dB, +60dB
- High
- 12kHz/±15dB
- Monitor Main Mono
- 4–8 ohm
- Low
- 80Hz/±15dB
- 8 Ohm per Channel
- 400W
- Dynamic
- s D/A 90dB
- Main L R
- 4–8 ohm
- Delay Time
- max. 5 secs
- Noise Thd N
- 0.002%/0.00018% A-weighted
- Sampling Rate
- 46.875kHz
- 4 Ohm per Channel
- 800W
- Fuse 100
- -120V T 10 A H 250V
- Fuse 220
- -240V T 6.3 A H 250V
- Mic E I N 20hz 20khz
- @ 0 ohm source resistance: -134dB/136dB A-weighted, @ 50 ohm source resistance: -131.5dB/134dB A-weighted, @ 150 ohm source resistance: -129dB/155dB A-weighted
- Signal Run Time Line in Gt Line Out
- approx. 1.5ms
